我有一个p0626代码和想知道诊断接头的列表…

你好,非常感谢您选择JustAnswer。抱歉听到你有这个问题的福特。我的名字是* * \ \ * \ \ * \ \ * * * * \ \ * \ \ *我将尽我所能协助这个问题。你可能会收到一个自动提示一个电话。有一个额外的收费电话和* *不* *是必需的。继续* *聊天* * * * * *是我的首选方法。* *(我有附加文档(s)到这个线程。请让我知道如果不出现在你的结束或打开文件,如果你有任何问题。注意:附件可能不会出现,如果您使用的是移动设备,从JustAnswer去你最后的电子邮件,您将看到附件。)注意:文档链接7天后将自动删除。* * P026 1。 First, measure voltage the voltage at the battery, then compare that voltage to the large battery cable at the alternator, and the battery sense wire at the 3 pin connector. (See the attached illustration.) The voltage should be the same if the cables, wiring and grounds are good. 2. If there is no voltage drop between the alternator and the batteries, then test the circuits between the PCM and alternator 3 pin connector. See the attached alternator control circuits' test. 3. If the powers to the alternator are good, and the control circuits test ok, suspect an alternator issue. [https://www.dropbox.com/s/60nni4eusjju3qi/Voltage%20Drop.pdf?dl=0](https://www.dropbox.com/s/60nni4eusjju3qi/Voltage%20Drop.pdf?dl=0) [https://www.dropbox.com/s/79pdm9mjcoqm71x/PCM.pdf?dl=0](https://www.dropbox.com/s/79pdm9mjcoqm71x/PCM.pdf?dl=0) [https://www.dropbox.com/s/31lf4g5umy444jk/P0626.pdf?dl=0](https://www.dropbox.com/s/31lf4g5umy444jk/P0626.pdf?dl=0) P1000 can be ignored - It means the OBD monitors have not reset since the last time the codes were cleared. The P0053 is an [oxygen sensor](/topics-oxygen-sensor-ford/) code. [https://www.dropbox.com/s/kvrz1eklhwkk4gg/P0053.pdf?dl=0](https://www.dropbox.com/s/kvrz1eklhwkk4gg/P0053.pdf?dl=0) Bear with me just a moment and I will provide the diagnostic steps for this code. I hope this helps. Please let me know if you have any questions. Note: If I don’t immediately respond, I kindly ask for your patience, I will reply as soon as possible. Thank you for choosing JustAnswer. 100% Customer Satisfaction is my goal. If you are satisfied with my answer please don’t forget to rate my service. (Where the stars are by “Rate my Service) If for any reason you are not satisfied with the answer I have provided, please let me know

P0052。1。首先,访问和把银行1传感器1。见附件说明。[https://www.dropbox.com/s/acq9ly9i2oki933/Bank%201%2002%20sensor%20location.pdf?dl=0] (https://www.dropbox.com/s/acq9ly9i2oki933/Bank%201%2002%20sensor%20location.pdf?dl=0) 2。负载测试电源加热电路,见附件说明。[https://www.dropbox.com/s/kpt1u5jkmchddwn/load%20test%20power%20circiut%20to%2002%20Sensor.pdf?dl=0] (https://www.dropbox.com/s/kpt1u5jkmchddwn/load%20test%20power%20circiut%20to%2002%20Sensor.pdf?dl=0) 3。如果权力是ok,测试电路的电阻加热器确保传感器本身并不开放。如果加热器传感器打开,更换故障传感器。4所示。 If the sensor is ok, access and unplug the [engine](/topics-engine-ford/) connector at the PCM. [https://www.dropbox.com/s/7m6hoghjlsprpz3/PCM%20to%20engine%20connector%20location.pdf?dl=0](https://www.dropbox.com/s/7m6hoghjlsprpz3/PCM%20to%20engine%20connector%20location.pdf?dl=0) 5. Test the oxygen sensor heater circuit. See the attached illustration. [https://www.dropbox.com/s/9os2mca6it46tuv/Testing%20the%20heater%20circuit.pdf?dl=0](https://www.dropbox.com/s/9os2mca6it46tuv/Testing%20the%20heater%20circuit.pdf?dl=0) 6. If there is no voltage to the oxygen sensor heater circuit at the PCM, repair the open wire between the PCM and the sensor. 7. If the heater circuit tests ok, swap the bank 1 and bank 2 heater circuits at the PCM engine connector, see the attached illustration. [https://www.dropbox.com/s/koyvb0lu4a7g4tf/Swapping%20the%20connector.pdf?dl=0](https://www.dropbox.com/s/koyvb0lu4a7g4tf/Swapping%20the%20connector.pdf?dl=0) 8. Plug the connector back in, clear all codes, then cycle the key and start the engine. 9. If the code moves to other sensor, suspect a harness or sensor issue, maybe try a different brand sensor. 10. If the code remains the same, suspect a failed PCM.