问:检查引擎代码P0014和P054A

asked byJuly 13, 2017

检查发动机灯已经打开。如果上周六换油,他们将我的卡车放在代码扫描仪上。最初带有2个无法识别的代码回来。昨晚把卡车带到了奥莱利的汽车零件,并拆散了它。2个确认的代码。P0014和P054A。两者似乎都与排气时机有关。这有多重要,我的下一步行动应该是什么?卡车展示(对我来说),没有其他我读过的“症状”。没有开始犹豫,MPG没有减少...实际上它略有改善。

事先感谢您的建议。

My car has 72500 miles.
My car has an automatic transmission.

检查引擎灯is on Inspection $94.99 - $114.99 获取报价

两个都代码请参阅可变阀正时机制的问题。该问题可能是机械的(基本时机关闭),液压(VVT依赖于发动机油压)或电气(有电磁阀,接线,端子)。不管问题如何,涉及的组件数量只有数量有限,某些项目,例如螺线管和关联的控制电路,都可以直接诊断。尽管有两个原因必须解决这样的问题:1)故障确实会降低发动机效率;2)如果由于存在故障而不断打开检查引擎灯,则在发动机控制中其他地方发生的任何新故障或其他故障的发生,您将基本上看不见您,因为无论如何检查引擎灯始终处于打开状态。换句话说,您希望关闭检查引擎的灯,以便您可以提醒问题。为了解决VVT问题,check engine light diagnosticis performed during which a certified mechanic from万博体育入口retrieves the codes from the PCM (that is, the specific codes that have caused the light to set) and then methodically tests the appropriate individual vehicle components or sub-systems to pinpoint the underlying fault. Once the faulty part or component is identified, it is explained to your satisfaction and the mechanic will let you know of the cost to repair. If you schedule the recommended diagnostic, the mechanic will resolve this promptly for you and all on a mobile basis right at your location. If you have further questions or concerns, do not hesitate to re-contact YourMechanic because we want you to make the most of your repair dollars and help you get the best possible results.

这些代码适用于排气凸轮轴传感器或凸轮轴对准问题。需要进行长时间的精确测试,以尝试验证传感器,接线或凸轮轴螺线管是否是问题。如果代码被清除并且不返回,请继续驱动驱动,直到灯光再次打开为止。如果这样做,则应进行精确测试以隔离原因。

The statements expressed above are only for informational purposes and should be independently verified. Please see ourterms of servicefor more details

Get an instant quote for your car

我们的认证力学来找您・以12万博亚洲客户端个月,12,000英里的保证为支持・公平和透明的定价manbet1


经验丰富的机械师?

赚取最多$ 70/小时

别人在问什么

我的交流还不够冷。
I would not recommend putting refrigerant into a car that you have been told is leaking. refrigerant is damaging to the environment, and the vehicle should be properly inspected for leaks before adding more refrigerant to the system, even if...
Code 1349 P
Hey there. Try having the compression checked for each cylinder. I have had experiences where this code pops up due to a lack of compression from a burned exhaust valve. Also, are you using the right fuel? Using inferior fuel...
Grinding noise in the front right of the vehicle.
Hi there: In most cases, when the wheel bearings go bad, they begin to make the grinding noise on turns, and is progressive as speed increases. This might be an issue with an inner axle (if you're Blazer if 4WD)...
汽车通常启动,有时曲柄约3-4秒
有很多原因引起了艰苦​​的启动,但说明性的是一个故障的发动机冷却液温度开关(传感器),空气感应系统问题,例如故障的怠速空气控制阀,磨损的火花塞,燃油输送不足或压力(堵塞燃油...
R53 ENG干扰是否
Hi there. If your timing chain has broken, you should take your Mini Cooper to a professional machine shop for service, as it's possible that you have internal engine damage.
P0089代码,燃油压力调节器性能低。进入li行模式,然后第二天早上没有开始
After doing a little research on your particular situation, it looks as though this is a fairly common problem with this model of vehicle. I would suggest contacting your local dealership about the situation due to the fact that I...
汽车在短途驾驶后奔跑。取代了恒温器和散热器风扇组件。
It sounds like you may have a water pump that may not be pumping correctly or may be failing. Generally, when a water pump is going bad, you may hear a bit of a whining sound combined with the pump...
Car stalls and oil pressure light flickers replaced ocv why is this happening
由于缺乏正常的油压,任何时候发动机降到一定的RPM水平时,机油压力灯可能会闪烁。如果最近更换了油压传感器,则应消除传感器作为潜在问题。
radiator and overflow full, car is steaming but not overheating according to indicator gauge. can i drive it?
嗨,隆达。感谢您今天与我们联系。您的恒温器或冷却液温度传感器很有可能是引起此问题的原因。如果仪表出现故障,它将导致冷却液的运行比应有的高温,从而创建...

Related articles

气帽不良或失败的症状
Common signs include the cap not tightening properly, a fuel smell in the car, and the Check Engine Light coming on.
P2401 OBD-II故障代码:EVAP泄漏检测泵控制电路低
P2401 P2401 trouble code definition P2401 is a OBD2 generic trouble code indicating a fault within the EVAP leak detection circuit. This code may be seen with other EVAP system codes. What the P2401 code means The P2401 trouble code...
P0343 OBD-II Trouble Code: Camshaft Position Sensor Circuit High Input
P0343 means theres a problem with the camshaft position sensor which has usually been fouled from oil and moisture causing a bad ground or voltage.